How to design a transtibial prosthetic socket using CAD software

Learn how to design a transtibial prosthetic socket using CAD software. Explore 3D scanning, anatomical marking, digital rectification and 3D printing with BenX.

BENX O&P PLATFORM

11/19/202623 min read

transtibial prosthetic socket
transtibial prosthetic socket

How to design a transtibial prosthetic socket using CAD software

Understanding the transtibial prosthetic socket

A transtibial prosthetic socket is designed to accommodate the residual limb below the knee. Its primary function is to provide an appropriate interface between the patient's residual limb and the prosthetic components.

The socket must address several clinical and biomechanical requirements:

• Distribute loads appropriately across the residual limb.

• Provide adequate relief for sensitive anatomical structures.

• Maintain suspension and rotational control.

• Accommodate changes in residual limb volume.

• Provide sufficient stability during standing and walking.

• Maintain comfort during different levels of physical activity.

Different socket designs use different approaches to load distribution and suspension.

Two commonly discussed approaches are:

Patellar tendon-bearing (PTB) socket: A traditional design approach that incorporates specific weight-bearing and relief areas, including consideration of the patellar tendon region.

Total surface bearing (TSB) socket: An approach that aims to distribute loading more broadly across the residual limb through a closely fitting interface, often used with an appropriate liner.

The choice of socket configuration depends on the patient's anatomy, tissue characteristics, activity level and clinical assessment.

Digital design software should support the prosthetist in implementing the selected clinical approach rather than dictate a universal socket shape.

Why use CAD software for transtibial socket design?

CAD software provides a digital environment in which the prosthetist can create, inspect and modify a three-dimensional socket model.

Compared with a conventional manual process, digital design offers several practical advantages.

1. Better control over measurements and geometry

A digital residual limb model allows the prosthetist to inspect its geometry from multiple directions and work with measurable dimensions.

✓ View the residual limb in three dimensions.

✓ Record and identify anatomical landmarks.

✓ Measure circumferences at defined levels.

✓ Apply controlled dimensional modifications.

✓ Review the resulting geometry before fabrication.

This makes it easier to understand how individual modifications influence the overall shape of the socket.

2. More efficient design modifications

In a conventional workflow, changing the geometry of a positive plaster model requires additional manual work.

In a digital workflow, modifications can be made directly to the model.

The prosthetist can adjust selected parameters, review the changes and retain previous versions where supported.

This can reduce repetitive work, particularly when several design iterations are required.

3. Improved repeatability and documentation

Digital models can be retained as part of the patient's design records.

This creates an opportunity to revisit previous designs, compare modifications and use earlier models as references when designing subsequent sockets.

The ability to retain the original scan and the modified model also makes it easier to understand how the final design was developed.

4. Direct integration with manufacturing

One of the most significant advantages of CAD-based prosthetic design is its connection with digital manufacturing.

The completed socket geometry can be exported in a suitable format and prepared for fabrication using technologies such as FDM or HP Multi Jet Fusion, subject to the relevant material and engineering requirements.

The result is a more connected process from patient assessment to digital design and manufacturing.

Step-by-step: How to design a transtibial prosthetic socket using CAD software

A digital transtibial socket design workflow can be divided into six principal stages.

Step 1: Capture the residual limb using 3D scanning

The first stage is obtaining an accurate three-dimensional representation of the patient's residual limb.

A suitable 3D scanning system captures the external surface geometry, creating a digital model that can be imported into prosthetic design software.

The scanning process should consider:

• Appropriate patient positioning.

• Consistent residual limb posture.

• Complete capture of the relevant anatomical region.

• Minimising movement during scanning.

• Avoiding missing surfaces and scanning artefacts.

The position of the knee, residual limb and surrounding soft tissue should be considered according to the intended socket design approach.

A good digital design starts with a good digital capture. Inaccuracies in the original scan can affect every subsequent stage.

Output: A three-dimensional residual limb model.

Step 2: Import the 3D model into prosthetic CAD software

Once the scan is complete, the model is imported into a dedicated prosthetic socket design platform.

Commonly used 3D file formats include:

• STL – widely used for surface geometry and 3D printing.

• OBJ – supports 3D geometry and associated surface information.

• PLY – commonly used for scanned 3D models and point-cloud-based data.

The software should preserve the relevant surface geometry and allow the prosthetist to inspect the model before starting rectification.

At this stage, the prosthetist should review:

✓ Overall model completeness.

✓ Surface quality and scanning artefacts.

✓ Residual limb orientation.

✓ Anatomical visibility.

✓ Relevant dimensions and circumferences.

The original scan should ideally be retained as an unmodified reference for comparison with the rectified model.

Step 3: Identify anatomical landmarks

Anatomical landmark identification is one of the most important stages of transtibial socket design.

The prosthetist needs to identify the relevant anatomical structures and understand their relationship with the intended socket geometry.

Important landmarks may include:

Patellar tendon: An important reference region in traditional PTB socket design.

Tibial crest: The anterior border of the tibia, which requires appropriate consideration during socket design.

Tibial tubercle: An important proximal anterior anatomical reference.

Fibular head: A region that generally requires careful attention to avoid excessive pressure.

Distal tibia: The distal bony prominence, which may require appropriate relief depending on the residual limb and socket design.

Distal fibula: Another important anatomical structure to consider during distal socket design.

Popliteal region: The posterior region behind the knee, which must be considered when establishing proximal socket geometry.

Digital landmark marking allows these references to be recorded directly on the 3D model.

The advantage is that the prosthetist can use the marked anatomy as a reference when applying subsequent modifications.

Step 4: Perform digital socket rectification

Rectification is the stage where the prosthetist translates clinical observations and design decisions into modifications of the residual limb geometry.

In a conventional workflow, this is achieved by modifying the positive plaster model.

In a digital workflow, the same clinical principles can be implemented through controlled CAD operations.

The exact modifications depend on the patient's anatomy and selected socket design.

A structured digital rectification process may include three important categories.

A. Global volume reduction

Global reduction involves modifying the overall volume of the residual limb model.

The prosthetist determines the appropriate reduction based on clinical assessment, tissue characteristics and the intended socket design.

A digital environment allows the reduction parameter to be controlled and the resulting geometry to be reviewed visually.

B. Circumferential reduction

Circumferential reduction involves adjusting the dimensions of the model at selected levels along the residual limb.

For example, circumference measurements may be evaluated at successive 5 cm intervals.

The prosthetist can define the required reductions at different levels rather than applying one uniform modification along the entire limb.

This is important because residual limb geometry and tissue characteristics vary along its length.

C. Zonal modifications

Some anatomical regions require specific modifications independent of the overall volume reduction.

These may include:

• Relief around the fibular head.

• Relief along the tibial crest.

• Appropriate consideration of the distal tibia.

• Modifications in the patellar tendon region.

• Posterior contour adjustments.

• Localised build-up or relief according to clinical requirements.

Zonal modifications allow the prosthetist to address specific anatomical requirements without relying entirely on global or circumferential changes.

An important principle: Digital rectification should not be treated as an automated mathematical exercise. The prosthetist must determine the appropriate modifications based on clinical assessment, intended load distribution and the patient's requirements.

Step 5: Review the rectified model and final socket geometry

After applying the required modifications, the prosthetist should carefully inspect the resulting digital model.

The review should include:

✓ Overall socket geometry.

✓ Anterior and posterior contours.

✓ Medial and lateral profiles.

✓ Proximal socket dimensions.

✓ Distal end geometry.

✓ Smooth transitions between modified regions.

✓ Areas that may require further clinical adjustment.

The model should be inspected from multiple directions to identify unwanted irregularities or unintended changes.

A digital environment makes this review process easier because the prosthetist can rotate the model, examine individual surfaces and compare the original scan with the modified geometry.

However, a visually acceptable CAD model does not automatically guarantee a clinically successful socket. Physical fitting and functional assessment remain essential.

Step 6: Prepare the design for 3D printing

Once the digital socket design is approved for manufacturing, the model can be prepared for the selected fabrication process.

Depending on the clinical application and manufacturing requirements, technologies such as FDM and HP Multi Jet Fusion may be considered.

Important manufacturing considerations include:

• Wall thickness and structural integrity.

• Material selection.

• Print orientation.

• Attachment and connector integration.

• Manufacturing tolerances.

• Surface quality and post-processing.

• Mechanical testing and applicable safety requirements.

The final design should be reviewed against the intended manufacturing process before production.

Output: A fabrication-ready digital socket model.

Understanding traditional versus digital transtibial socket design

Digital design does not make traditional prosthetic techniques irrelevant.

Plaster casting and manual rectification have been developed through decades of clinical experience and remain valuable methods of socket fabrication.

The difference lies in how the design information is captured, modified and transferred to manufacturing.

Comparison table contrasting traditional plaster casting methods with modern digital 3D scanning approaches for prosthetics.
Comparison table contrasting traditional plaster casting methods with modern digital 3D scanning approaches for prosthetics.

The biggest opportunity offered by digital design is not simply faster modelling.

It is the ability to retain, review and modify the design with greater control and connect the design process more directly with manufacturing.

For an O&P clinic handling multiple patients, this can create a more organised and scalable design environment.

What should you look for in transtibial socket design software?

Not all 3D CAD platforms are designed for prosthetic applications.

General-purpose CAD software may offer sophisticated modelling capabilities, but prosthetic socket design requires a more specialised understanding of anatomy and clinical rectification.

When selecting transtibial socket design software, consider the following:

• 3D file compatibility: Support for commonly used scanning formats such as STL, OBJ and PLY.

• Anatomical landmark marking: Ability to identify and record important anatomical reference points.

• Structured rectification: Tools for global, circumferential and zonal modifications.

• Visualisation: Ability to inspect the model from different directions and understand the effect of modifications.

• Design flexibility: Ability to accommodate different socket configurations and patient-specific requirements.

• Manufacturing compatibility: Preparation of models for appropriate fabrication technologies.

• Ease of use: A workflow that allows prosthetists to concentrate on clinical design rather than complicated software operations.

The most useful software is not necessarily the one with the greatest number of modelling tools. It is the one that makes clinically relevant design operations accessible, measurable and repeatable.

How BenX supports digital below-knee socket design

BenX, developed by BenGait Labs, is a dedicated digital design platform for prosthetics and orthotics professionals.

Its approach is based on connecting 3D scanning, structured digital rectification and manufacturing preparation.

For below-knee socket design, BenX provides a workflow that allows prosthetists to work with imported 3D residual limb models and perform structured modifications.

1. Importing residual limb scans

BenX supports STL, OBJ and PLY file formats, allowing compatible 3D scans to be imported into the design environment.

This gives O&P professionals flexibility in selecting their scanning equipment.

2. Anatomical landmark identification

The prosthetist can identify relevant anatomical reference points on the residual limb model.

These markings provide a reference for the subsequent rectification process.

3. Three-stage rectification approach

BenX provides structured controls for three important categories of BK socket rectification:

Global reduction: Control over the overall volume reduction of the residual limb model.

Circumferential reduction: Defined reductions at successive levels, including approximately 5 cm intervals.

Zonal modifications: Localised modifications to specific anatomical regions based on clinical requirements.

This approach provides an organised digital environment for implementing clinical decisions.

4. Digital model review

The prosthetist can review the resulting 3D geometry and assess the effect of the modifications.

The ability to inspect the model visually provides an additional level of control before proceeding to manufacturing.

5. Preparation for digital manufacturing

The completed digital model can form the basis for subsequent manufacturing, including preparation for suitable FDM or HP Multi Jet Fusion workflows.

The objective is to connect the socket design process with the broader digital manufacturing ecosystem.

The future of transtibial prosthetic design: Beyond CAD modelling

The adoption of digital technology in prosthetics is likely to extend beyond replacing individual manual operations.

The next stage is the development of integrated workflows connecting patient assessment, 3D scanning, design, manufacturing and subsequent review.

This creates several opportunities for O&P practices.

✓ Digital patient models can be retained for future reference.

✓ Design parameters can be documented and reviewed.

✓ Modifications can be made without recreating the original physical model.

✓ Design information can be shared with manufacturing teams.

✓ AI-assisted tools may help support certain repetitive design tasks in the future.

✓ Additive manufacturing can enable new approaches to patient-specific fabrication.

However, these developments should be guided by clinical validation and engineering requirements.

The role of the prosthetist remains central. Technology should improve the ability to make informed decisions, not replace the responsibility for those decisions.

Research supporting digital prosthetic socket design

Research in prosthetics is increasingly examining the use of 3D scanning, CAD-based rectification and additive manufacturing.

One particularly relevant study published in Scientific Reports in October 2024 compared a digital design methodology with conventional design approaches for transtibial prosthetic interfaces.

The study evaluated a customised digital methodology using medical imaging and computational modelling.

The findings included improvements in certain comfort and pressure-related outcomes for the digitally designed interfaces.

This research is important because it demonstrates how digital design can be used to explore patient-specific interface geometry rather than simply reproducing a conventional socket shape in a computer environment.

The study was based on a specific research methodology and should not be interpreted as evidence that every digital socket design method will produce the same results.

Read the research: A clinical comparison of a digital versus conventional design methodology for transtibial prosthetic interfaces – Scientific Reports, 2024

A second relevant area is additive manufacturing. Research into 3D-printed transtibial sockets is examining how different materials, geometries and manufacturing methods can be used to develop patient-specific prosthetic components.

This research supports the broader transition towards connected digital design and manufacturing.

Frequently Asked Questions (FAQs)

1. How do you design a transtibial prosthetic socket using CAD software?

The process generally involves capturing the residual limb using 3D scanning, importing the model into prosthetic CAD software, identifying anatomical landmarks, applying the required rectification, reviewing the resulting geometry and preparing the model for manufacturing.

2. What is transtibial socket design software?

Transtibial socket design software is a computer-aided design platform used to create and modify below-knee prosthetic sockets. It enables prosthetists to work with 3D residual limb models and apply clinical modifications digitally.

3. Can a below-knee prosthetic socket be designed using a 3D scan?

Yes. A 3D scan can capture the external geometry of the residual limb and provide a digital reference for socket design. The quality of the scan, patient positioning and clinical assessment are important for obtaining a useful model.

4. What are the important anatomical landmarks in transtibial socket design?

Important landmarks include the patellar tendon region, tibial crest, tibial tubercle, fibular head, distal tibia, distal fibula and popliteal region. Their relevance depends on the selected socket design and the patient's anatomy.

5. What is digital socket rectification?

Digital socket rectification is the process of modifying a 3D residual limb model using CAD software to create the intended socket geometry. It may involve overall volume reduction, circumferential changes and localised anatomical modifications.

6. Is digital socket design more accurate than manual plaster rectification?

Digital design offers better numerical control, measurable modifications and the ability to retain design records. However, accuracy depends on scan quality, clinical inputs and the prosthetist's expertise. Digital technology should complement established clinical methods.

7. Can CAD-designed transtibial sockets be 3D printed?

Yes. CAD-designed sockets can be prepared for additive manufacturing using suitable FDM or other 3D printing technologies. The design must meet appropriate material, structural and clinical requirements before use.

8. Which file formats are commonly used for prosthetic socket design?

STL, OBJ and PLY are commonly used formats for 3D scanning and surface geometry. Their suitability depends on the scanning system and the capabilities of the design software.

Conclusion: Bringing clinical expertise into the digital design era

Transtibial prosthetic socket design has traditionally been built around the clinical knowledge and practical experience of prosthetists.

The introduction of 3D scanning and CAD-based design is creating opportunities to make this process more structured, measurable and efficient.

Digital technology allows professionals to work with three-dimensional anatomical models, apply controlled rectification and retain digital records that can be revisited when modifications are required.

It also provides a direct pathway towards additive manufacturing, connecting the clinical design process with modern fabrication technologies.

The objective is not to replace traditional expertise. It is to extend that expertise through tools that offer greater control, repeatability and integration.

BenX by BenGait Labs brings this philosophy into prosthetic and orthotic design, providing a dedicated digital environment for below-knee socket design and structured rectification.

The future of prosthetic design will be driven by the combination of experienced clinical judgement and the capabilities of digital technology.

Explore BenX and move towards a more connected approach to prosthetic socket design.

Visit: https://www.bengaitlabs.com/

Introduction

Designing a transtibial (below-knee) prosthetic socket requires a combination of anatomical understanding, clinical assessment and technical expertise. The socket must provide a comfortable interface with the residual limb while ensuring appropriate load transfer, suspension, stability and control of the prosthesis.

Traditionally, this process has involved plaster casting, preparation of a positive model and manual rectification by an experienced prosthetist. These methods remain valuable and continue to be widely practised across prosthetics and orthotics clinics.

However, advances in 3D scanning, computer-aided design (CAD) and additive manufacturing are changing how prosthetic sockets can be designed and manufactured.

With digital prosthetic design software, the prosthetist can work directly with a three-dimensional model of the residual limb, identify anatomical landmarks, apply controlled modifications and prepare the resulting geometry for manufacturing.

The advantage is not simply that the plaster model is replaced by a digital model. It is that the design process becomes more measurable, easier to modify and capable of being integrated with digital manufacturing.

This article explains how to design a transtibial prosthetic socket using CAD software, the important stages of digital rectification and how dedicated platforms such as BenX can support this workflow.

transtibial prosthetic socket
transtibial prosthetic socket

How to design a transtibial prosthetic socket using CAD software

Understanding the transtibial prosthetic socket

A transtibial prosthetic socket is designed to accommodate the residual limb below the knee. Its primary function is to provide an appropriate interface between the patient's residual limb and the prosthetic components.

The socket must address several clinical and biomechanical requirements:

• Distribute loads appropriately across the residual limb.

• Provide adequate relief for sensitive anatomical structures.

• Maintain suspension and rotational control.

• Accommodate changes in residual limb volume.

• Provide sufficient stability during standing and walking.

• Maintain comfort during different levels of physical activity.

Different socket designs use different approaches to load distribution and suspension.

Two commonly discussed approaches are:

Patellar tendon-bearing (PTB) socket: A traditional design approach that incorporates specific weight-bearing and relief areas, including consideration of the patellar tendon region.

Total surface bearing (TSB) socket: An approach that aims to distribute loading more broadly across the residual limb through a closely fitting interface, often used with an appropriate liner.

The choice of socket configuration depends on the patient's anatomy, tissue characteristics, activity level and clinical assessment.

Digital design software should support the prosthetist in implementing the selected clinical approach rather than dictate a universal socket shape.

Why use CAD software for transtibial socket design?

CAD software provides a digital environment in which the prosthetist can create, inspect and modify a three-dimensional socket model.

Compared with a conventional manual process, digital design offers several practical advantages.

1. Better control over measurements and geometry

A digital residual limb model allows the prosthetist to inspect its geometry from multiple directions and work with measurable dimensions.

✓ View the residual limb in three dimensions.

✓ Record and identify anatomical landmarks.

✓ Measure circumferences at defined levels.

✓ Apply controlled dimensional modifications.

✓ Review the resulting geometry before fabrication.

This makes it easier to understand how individual modifications influence the overall shape of the socket.

2. More efficient design modifications

In a conventional workflow, changing the geometry of a positive plaster model requires additional manual work.

In a digital workflow, modifications can be made directly to the model.

The prosthetist can adjust selected parameters, review the changes and retain previous versions where supported.

This can reduce repetitive work, particularly when several design iterations are required.

3. Improved repeatability and documentation

Digital models can be retained as part of the patient's design records.

This creates an opportunity to revisit previous designs, compare modifications and use earlier models as references when designing subsequent sockets.

The ability to retain the original scan and the modified model also makes it easier to understand how the final design was developed.

4. Direct integration with manufacturing

One of the most significant advantages of CAD-based prosthetic design is its connection with digital manufacturing.

The completed socket geometry can be exported in a suitable format and prepared for fabrication using technologies such as FDM or HP Multi Jet Fusion, subject to the relevant material and engineering requirements.

The result is a more connected process from patient assessment to digital design and manufacturing.

Step-by-step: How to design a transtibial prosthetic socket using CAD software

A digital transtibial socket design workflow can be divided into six principal stages.

Step 1: Capture the residual limb using 3D scanning

The first stage is obtaining an accurate three-dimensional representation of the patient's residual limb.

A suitable 3D scanning system captures the external surface geometry, creating a digital model that can be imported into prosthetic design software.

The scanning process should consider:

• Appropriate patient positioning.

• Consistent residual limb posture.

• Complete capture of the relevant anatomical region.

• Minimising movement during scanning.

• Avoiding missing surfaces and scanning artefacts.

The position of the knee, residual limb and surrounding soft tissue should be considered according to the intended socket design approach.

A good digital design starts with a good digital capture. Inaccuracies in the original scan can affect every subsequent stage.

Output: A three-dimensional residual limb model.

Step 2: Import the 3D model into prosthetic CAD software

Once the scan is complete, the model is imported into a dedicated prosthetic socket design platform.

Commonly used 3D file formats include:

• STL – widely used for surface geometry and 3D printing.

• OBJ – supports 3D geometry and associated surface information.

• PLY – commonly used for scanned 3D models and point-cloud-based data.

The software should preserve the relevant surface geometry and allow the prosthetist to inspect the model before starting rectification.

At this stage, the prosthetist should review:

✓ Overall model completeness.

✓ Surface quality and scanning artefacts.

✓ Residual limb orientation.

✓ Anatomical visibility.

✓ Relevant dimensions and circumferences.

The original scan should ideally be retained as an unmodified reference for comparison with the rectified model.

Step 3: Identify anatomical landmark

Anatomical landmark identification is one of the most important stages of transtibial socket design.

The prosthetist needs to identify the relevant anatomical structures and understand their relationship with the intended socket geometry.

Important landmarks may include:

Patellar tendon: An important reference region in traditional PTB socket design.

Tibial crest: The anterior border of the tibia, which requires appropriate consideration during socket design.

Tibial tubercle: An important proximal anterior anatomical reference.

Fibular head: A region that generally requires careful attention to avoid excessive pressure.

Distal tibia: The distal bony prominence, which may require appropriate relief depending on the residual limb and socket design.

Distal fibula: Another important anatomical structure to consider during distal socket design.

Popliteal region: The posterior region behind the knee, which must be considered when establishing proximal socket geometry.

Digital landmark marking allows these references to be recorded directly on the 3D model.

The advantage is that the prosthetist can use the marked anatomy as a reference when applying subsequent modifications.

Step 4: Perform digital socket rectification

Rectification is the stage where the prosthetist translates clinical observations and design decisions into modifications of the residual limb geometry.

In a conventional workflow, this is achieved by modifying the positive plaster model.

In a digital workflow, the same clinical principles can be implemented through controlled CAD operations.

The exact modifications depend on the patient's anatomy and selected socket design.

A structured digital rectification process may include three important categories.

Comparison table contrasting traditional plaster casting methods with modern digital 3D scanning approaches for prosthetics.
Comparison table contrasting traditional plaster casting methods with modern digital 3D scanning approaches for prosthetics.

The biggest opportunity offered by digital design is not simply faster modelling.

It is the ability to retain, review and modify the design with greater control and connect the design process more directly with manufacturing.

For an O&P clinic handling multiple patients, this can create a more organised and scalable design environment.

What should you look for in transtibial socket design software?

Not all 3D CAD platforms are designed for prosthetic applications.

General-purpose CAD software may offer sophisticated modelling capabilities, but prosthetic socket design requires a more specialised understanding of anatomy and clinical rectification.

When selecting transtibial socket design software, consider the following:

• 3D file compatibility: Support for commonly used scanning formats such as STL, OBJ and PLY.

• Anatomical landmark marking: Ability to identify and record important anatomical reference points.

• Structured rectification: Tools for global, circumferential and zonal modifications.

• Visualisation: Ability to inspect the model from different directions and understand the effect of modifications.

• Design flexibility: Ability to accommodate different socket configurations and patient-specific requirements.

• Manufacturing compatibility: Preparation of models for appropriate fabrication technologies.

• Ease of use: A workflow that allows prosthetists to concentrate on clinical design rather than complicated software operations.

The most useful software is not necessarily the one with the greatest number of modelling tools. It is the one that makes clinically relevant design operations accessible, measurable and repeatable.

How BenX supports digital below-knee socket design

BenX, developed by BenGait Labs, is a dedicated digital design platform for prosthetics and orthotics professionals.

Its approach is based on connecting 3D scanning, structured digital rectification and manufacturing preparation.

For below-knee socket design, BenX provides a workflow that allows prosthetists to work with imported 3D residual limb models and perform structured modifications.

1. Importing residual limb scans

BenX supports STL, OBJ and PLY file formats, allowing compatible 3D scans to be imported into the design environment.

This gives O&P professionals flexibility in selecting their scanning equipment.

2. Anatomical landmark identification

The prosthetist can identify relevant anatomical reference points on the residual limb model.

These markings provide a reference for the subsequent rectification process.

3. Three-stage rectification approach

BenX provides structured controls for three important categories of BK socket rectification:

Global reduction: Control over the overall volume reduction of the residual limb model.

Circumferential reduction: Defined reductions at successive levels, including approximately 5 cm intervals.

Zonal modifications: Localised modifications to specific anatomical regions based on clinical requirements.

This approach provides an organised digital environment for implementing clinical decisions.

4. Digital model review

The prosthetist can review the resulting 3D geometry and assess the effect of the modifications.

The ability to inspect the model visually provides an additional level of control before proceeding to manufacturing.

5. Preparation for digital manufacturing

The completed digital model can form the basis for subsequent manufacturing, including preparation for suitable FDM or HP Multi Jet Fusion workflows.

The objective is to connect the socket design process with the broader digital manufacturing ecosystem.

The future of transtibial prosthetic design: Beyond CAD modelling

The adoption of digital technology in prosthetics is likely to extend beyond replacing individual manual operations.

The next stage is the development of integrated workflows connecting patient assessment, 3D scanning, design, manufacturing and subsequent review.

This creates several opportunities for O&P practices.

✓ Digital patient models can be retained for future reference.

✓ Design parameters can be documented and reviewed.

✓ Modifications can be made without recreating the original physical model.

✓ Design information can be shared with manufacturing teams.

✓ AI-assisted tools may help support certain repetitive design tasks in the future.

✓ Additive manufacturing can enable new approaches to patient-specific fabrication.

However, these developments should be guided by clinical validation and engineering requirements.

The role of the prosthetist remains central. Technology should improve the ability to make informed decisions, not replace the responsibility for those decisions.

Research supporting digital prosthetic socket design

Research in prosthetics is increasingly examining the use of 3D scanning, CAD-based rectification and additive manufacturing.

One particularly relevant study published in Scientific Reports in October 2024 compared a digital design methodology with conventional design approaches for transtibial prosthetic interfaces.

The study evaluated a customised digital methodology using medical imaging and computational modelling.

The findings included improvements in certain comfort and pressure-related outcomes for the digitally designed interfaces.

This research is important because it demonstrates how digital design can be used to explore patient-specific interface geometry rather than simply reproducing a conventional socket shape in a computer environment.

The study was based on a specific research methodology and should not be interpreted as evidence that every digital socket design method will produce the same results.

Read the research: A clinical comparison of a digital versus conventional design methodology for transtibial prosthetic interfaces – Scientific Reports, 2024

A second relevant area is additive manufacturing. Research into 3D-printed transtibial sockets is examining how different materials, geometries and manufacturing methods can be used to develop patient-specific prosthetic components.

This research supports the broader transition towards connected digital design and manufacturing.

Frequently Asked Questions (FAQs)

1. How do you design a transtibial prosthetic socket using CAD software?

The process generally involves capturing the residual limb using 3D scanning, importing the model into prosthetic CAD software, identifying anatomical landmarks, applying the required rectification, reviewing the resulting geometry and preparing the model for manufacturing.

2. What is transtibial socket design software?

Transtibial socket design software is a computer-aided design platform used to create and modify below-knee prosthetic sockets. It enables prosthetists to work with 3D residual limb models and apply clinical modifications digitally.

3. Can a below-knee prosthetic socket be designed using a 3D scan?

Yes. A 3D scan can capture the external geometry of the residual limb and provide a digital reference for socket design. The quality of the scan, patient positioning and clinical assessment are important for obtaining a useful model.

4. What are the important anatomical landmarks in transtibial socket design?

Important landmarks include the patellar tendon region, tibial crest, tibial tubercle, fibular head, distal tibia, distal fibula and popliteal region. Their relevance depends on the selected socket design and the patient's anatomy.

5. What is digital socket rectification?

Digital socket rectification is the process of modifying a 3D residual limb model using CAD software to create the intended socket geometry. It may involve overall volume reduction, circumferential changes and localised anatomical modifications.

6. Is digital socket design more accurate than manual plaster rectification?

Digital design offers better numerical control, measurable modifications and the ability to retain design records. However, accuracy depends on scan quality, clinical inputs and the prosthetist's expertise. Digital technology should complement established clinical methods.

7. Can CAD-designed transtibial sockets be 3D printed?

Yes. CAD-designed sockets can be prepared for additive manufacturing using suitable FDM or other 3D printing technologies. The design must meet appropriate material, structural and clinical requirements before use.

8. Which file formats are commonly used for prosthetic socket design?

STL, OBJ and PLY are commonly used formats for 3D scanning and surface geometry. Their suitability depends on the scanning system and the capabilities of the design software.

Conclusion: Bringing clinical expertise into the digital design era

Transtibial prosthetic socket design has traditionally been built around the clinical knowledge and practical experience of prosthetists.

The introduction of 3D scanning and CAD-based design is creating opportunities to make this process more structured, measurable and efficient.

Digital technology allows professionals to work with three-dimensional anatomical models, apply controlled rectification and retain digital records that can be revisited when modifications are required.

It also provides a direct pathway towards additive manufacturing, connecting the clinical design process with modern fabrication technologies.

The objective is not to replace traditional expertise. It is to extend that expertise through tools that offer greater control, repeatability and integration.

BenX by BenGait Labs brings this philosophy into prosthetic and orthotic design, providing a dedicated digital environment for below-knee socket design and structured rectification.

The future of prosthetic design will be driven by the combination of experienced clinical judgement and the capabilities of digital technology.

Explore BenX and move towards a more connected approach to prosthetic socket design.

Visit: https://www.bengaitlabs.com/

Introduction

Designing a transtibial (below-knee) prosthetic socket requires a combination of anatomical understanding, clinical assessment and technical expertise. The socket must provide a comfortable interface with the residual limb while ensuring appropriate load transfer, suspension, stability and control of the prosthesis.

Traditionally, this process has involved plaster casting, preparation of a positive model and manual rectification by an experienced prosthetist. These methods remain valuable and continue to be widely practised across prosthetics and orthotics clinics.

However, advances in 3D scanning, computer-aided design (CAD) and additive manufacturing are changing how prosthetic sockets can be designed and manufactured.

With digital prosthetic design software, the prosthetist can work directly with a three-dimensional model of the residual limb, identify anatomical landmarks, apply controlled modifications and prepare the resulting geometry for manufacturing.

The advantage is not simply that the plaster model is replaced by a digital model. It is that the design process becomes more measurable, easier to modify and capable of being integrated with digital manufacturing.

This article explains how to design a transtibial prosthetic socket using CAD software, the important stages of digital rectification and how dedicated platforms such as BenX can support this workflow.

A. Global volume reduction

Global reduction involves modifying the overall volume of the residual limb model.

The prosthetist determines the appropriate reduction based on clinical assessment, tissue characteristics and the intended socket design.

A digital environment allows the reduction parameter to be controlled and the resulting geometry to be reviewed visually.

B. Circumferential reduction

Circumferential reduction involves adjusting the dimensions of the model at selected levels along the residual limb.

For example, circumference measurements may be evaluated at successive 5 cm intervals.

The prosthetist can define the required reductions at different levels rather than applying one uniform modification along the entire limb.

This is important because residual limb geometry and tissue characteristics vary along its length.

C. Zonal modifications

Some anatomical regions require specific modifications independent of the overall volume reduction.

These may include:

• Relief around the fibular head.

• Relief along the tibial crest.

• Appropriate consideration of the distal tibia.

• Modifications in the patellar tendon region.

• Posterior contour adjustments.

• Localised build-up or relief according to clinical requirements.

Zonal modifications allow the prosthetist to address specific anatomical requirements without relying entirely on global or circumferential changes.

An important principle: Digital rectification should not be treated as an automated mathematical exercise. The prosthetist must determine the appropriate modifications based on clinical assessment, intended load distribution and the patient's requirements.

Step 5: Review the rectified model and final socket geometry

After applying the required modifications, the prosthetist should carefully inspect the resulting digital model.

The review should include:

✓ Overall socket geometry.

✓ Anterior and posterior contours.

✓ Medial and lateral profiles.

✓ Proximal socket dimensions.

✓ Distal end geometry.

✓ Smooth transitions between modified regions.

✓ Areas that may require further clinical adjustment.

The model should be inspected from multiple directions to identify unwanted irregularities or unintended changes.

A digital environment makes this review process easier because the prosthetist can rotate the model, examine individual surfaces and compare the original scan with the modified geometry.

However, a visually acceptable CAD model does not automatically guarantee a clinically successful socket. Physical fitting and functional assessment remain essential.

Step 6: Prepare the design for 3D printing

Once the digital socket design is approved for manufacturing, the model can be prepared for the selected fabrication process.

Depending on the clinical application and manufacturing requirements, technologies such as FDM and HP Multi Jet Fusion may be considered.

Important manufacturing considerations include:

• Wall thickness and structural integrity.

• Material selection.

• Print orientation.

• Attachment and connector integration.

• Manufacturing tolerances.

• Surface quality and post-processing.

• Mechanical testing and applicable safety requirements.

The final design should be reviewed against the intended manufacturing process before production.

Output: A fabrication-ready digital socket model.

Understanding traditional versus digital transtibial socket design

Digital design does not make traditional prosthetic techniques irrelevant.

Plaster casting and manual rectification have been developed through decades of clinical experience and remain valuable methods of socket fabrication.

The difference lies in how the design information is captured, modified and transferred to manufacturing.